The Solera awning fabric like the part # LCV000334438 that you referenced does only have the one bead but it would work fine on your roller that does have two slots. It would just install into one of the beads and you'd be set. view full answer...
Since you already have your leaf springs above the axle you cannot use an over-under kit like Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00. Instead, your only safe option is to use taller suspension hangers. I attached a link which shows the various sizes of hangers for trailers; you will want to match something up that fits your trailer and is slightly taller than your current hangers to gain the desired lift. view full answer...
There aren't any companies making spacers or cover plates so you'd have to get a residential cover plate from your local hardware store and cut it down to fit. You do have to be careful though that you don't go too thick with the cover plate so you can still stay within the 1-1/2" maximum door thickness of the Global Link RV Entry Door Locking Latch Kit # 295-000021. You'll also want to use a bit of sealant around the cover plate edge to prevent any water from leaking in.
As for the spacer... view full answer...
I'm not sure what you mean by upgrade but we do have the correct replacement bearings for your trailer, the Bearing Kit part # BK3-200 which contains bearings, races, and seals. This is a direct match for the Lippert Bearing Kit 333951.
Please note, if you're having issues with your existing bearings then you should know that the main reason they fail is because of improper lubrication. Therefore, you'll need to make sure you repack them every year and add grease as needed. view full answer...
The U-bolts that come with the CE Smith Post-Style Guide-Ons for Boat Trailers part # CE27646 are compatible with c channels like what you have on your trailer but they fit channels up to 4-1/4" tall. There is longer hardware available with part # CE11416 which fits channels up to 5-1/4" tall. That is the longest U-bolt hardware for the CE Smith Guide-ons available or any other Guide on at this time. view full answer...
I may have a solution for you, but the closest replacement kitchen sink would be the LaSalle Bristol Double Bowl RV Kitchen Sink - 33" Long x 19" Wide - Stainless Steel # 34413TGS331974, which is a bit larger than your current sink and would likely require some modification of the rough opening to use. The overall dimensions of this sink are 33" long and 19" wide, and the bowls require a roughly 30" long and 14" wide cutout.
This is a drop-in sink. view full answer...
The Electric Motor # LG-142178 will work with the Gearbox # LC276602 which is compatible with most 5th wheel landing gear sets on the market. Unless you have a really oddball landing gear set you'll be good to go. If you are unsure about what you have just send me some photos and I can take a look for you.
I've attached a video showing the motor being installed that you can compare with what you have. view full answer...
I recommend using the MaxxAir FanMate Rain Cover # MA00-955003 for your model 8100TS Fan-Tastic roof vents. This rain cover comes with brackets that allow it to install on any vent. Check out the installation video that I have linked for you to reference.
If you would rather have this cover in white you will need to use part # MA00-955001 instead. view full answer...
To find out if the Lippert Components 32" Lead, part # LC179013, will work with your 5th wheel, you need to check your current one against this one to see if it matches. Key measurements of this leg are:
Bracket Stop - 17-1/2"
Height with one hole out for foot plate attachment - 32"
Capacity - Manual (4000 lbs), Single Motor (2500 lbs), and Dual Motor (4000 lbs)
Travel Distance: 21"
Drop Leg Travel: 16"
I've linked to a video below that will help you find out how to measure these.
Finally,... view full answer...